I am now evaluating Direwolf for HF packet reception on 10.1476MHz. It’s running on a Rasperry Pi 2 with the cheapo Cmedia sound card and the performance looks extremely good. I just need to figure out why I’m getting broken pipe errors though.
I haven’t yet decided whether to run it as stand-alone igate or use it as a TNC in conjunction with Xastir as it provides either AGWPE or KISS type interfaces to external programs.
Update 13th May – I reduced the number of parallel modems from 7 to 3 and this seems to have cured the broken pipe errors. I’m now gating received traffic to APRS-IS using the built-in client. Traffic reported can be seen on aprs.link.
I’ve made some changes to the Multimode setup to give it more flexibility.
The main feature is that I’ve added the SV1AGW Packet Engine – AGWPE. This is an extremely flexible program that allows me to share the SCS Tracker (or any other TNC) over a tcp/ip connection. I just needed to change the APRSIS32 port configuration from a KISS serial port to a second AGWPE port and configure AGWPE itself to allow connections on 8001/tcp. (8000/tcp is already in use by UZ7HO SounddModem).
This now allows me to run an AX25 monitor program (such as UZ7HO’s EasyTerm) so I can trace activity on the RPR channel.
Developing things further, AGWPE and UZ7HO_SM accept multiple tcp connections and therefore multipe applications can share a single TNC (unfortunately Messenger doesn’t yet). I can now make connections from other hosts on my network, for example I have Xastir running on a Rasperyy Pi connecting to AGWPE. I’m now considering running just the TNC/modem radio interfaces on the shack PC and the APRS applications can live elsewhere!
Download aprsis32_multimode system diagram – PDF.
I’ve been experimenting with APRS on 10MHz. Mainly reception at home and also some portable operation. After spending some time with UIview32, I changed over to APRSISCE/32 which I find more suitable for my needs.
For 300baud FSK packet I use the UZ7HO SoundModem. This uses a soundcard for TX and RX and emulates the AGW Packet Engine interface. It can be configured to use two audio frequencies simultaneously and has a waterfall display to aid tuning.
Chris G4HYG has just released version 3.29 of his APRS Messenger program. Not only does this interface with a standard TNC. It also supports sending and receiving APRS traffic over PSK, GMSK and MFSK16 modes. This makes use of the MMVARI engine which he has configured to run as multiple receivers. It will also connect the the UZ7HO SoundModem but presently this only works on receive. Stephen WA8LMF has also written some extensive notes on configuring APRS Messenger and using with UIview.
APRSISCE/32 is more flexible in this respect, so I configured an additional text port to connect to APRS Messenger port 8063. In this setup, APRS Messenger is used purely as a PSK/GMSK/MFSK16 receive decoder.
Finally I bought the SCS-Tracker TNC. After placing my order back in April, I had a few months to wait due to a re-design of the enclosure. This is configured to run in Robust Packet Mode and connects to the APRSISCE/32 host using KISS protocol over a USB serial connection.
Audio Frequency Settings
- The receiver is set to 10147.30kHz USB dial frequency.
- A PBT offset of +500Hz shifts the top end of the audio passband up to 3kHz.
- The HF modems in APRS Messenger are set for 2400Hz.
- The HF modem in UZ7HO SoundModem is set for 2000Hz.
- The RPR modem in the SCS Tracker is set for 1500Hz.
Both APRS Messenger share the same sound card. Both applications should be set for a sampling frequency of 11025kHz and the SoundModem should be calibrated for best results.
APRSCE/32 Port Settings
- APRS-IS – Your normal APRS Internet connection (not shown in the diagram).
- KISS TNC – connected to SCS-Tracker TNC via USB.
- UZ7HO_SM – AGWPE connection to tcp/ip 127.0.0.1 port 8000.
- APRS_MSGR – TEXT connection to tcp/ip 127.0.0.1 port 8063.
10Mhz APRS seems quite active and I’m hearing a lot of traffic on RPR, probably more than on 300baud FSK. There isn’t much PSK/MFSK activity and I’m hoping to contribite to that mode with my portable setup.
See the system diagram above (click on it for full size or download the PDF!) to see how it all fits together.
Check the Digipeater Users list at DB0ANF.
I’ve just started experimenting with WSPR – a weak signals digital mode, using the Icom IC703 and 5W to a 15m end-fed wire. I’d been transmitting on and off for around an hour, checking in the WSPRnet spots database to see how far away I was being copied.
Imagine my surprise when I saw this one.
2014-05-20 19:32 G4IRX 10.140155 -26 0 IO92jv 5 VK5MR PF96lh 16221 72
I double-checked VK5MR’s reported spots – he was hearing lots of EU and some Japanese traffic so I guess he must be operating from home! Now if only I could get that far on 10MHz APRS…